Most 12V problems in an overland build aren’t caused by the battery or the fridge. They come from the wire in between. A cable that is too thin for its length loses voltage on the way, so the fridge cuts out early, the compressor runs slowly and the DC-DC charger never quite fills the battery. In the worst case, the cable gets hot. The good news is that choosing the right 12V wire size is simple once you know the two numbers that matter: current and length.
Why voltage drop matters more at 12V
Every wire has some resistance, so some voltage is lost along it. On a 230V or 120V house circuit, losing half a volt is nothing. At 12V, however, half a volt is about 4% of everything you have. Many 12V devices also have a low-voltage cut-off, so a fridge on a long, thin cable can switch itself off while the battery still has plenty left.
Blue Sea Systems, whose chart is widely used for boats and vehicles, suggests a maximum 3% drop for anything important (electronics, fridges, panel supply cables) and up to 10% for less critical loads such as cabin lights. For an overland build, 3% is a sensible target for almost everything.
Measure the round trip, not just the run
This is the mistake most people make. Current flows out on the positive wire and back on the negative, so the length you use for sizing is the full loop: from the battery to the device and back again. A fridge 10 feet from the battery is on a 20-foot circuit. If the negative goes to a chassis ground instead, the chassis is part of that loop too, and a poor ground adds resistance you can’t see.
12V wire size table
We worked out the table below from standard copper resistance figures for a 3% drop at 12V (0.36V). The distance is one way, from battery to device. Round up to a thicker wire if you’re between sizes, if the cable runs through a hot engine bay, or if it is bundled with other cables.
| Current | 5 ft | 10 ft | 15 ft | 20 ft |
|---|---|---|---|---|
| 5 A (LED lights, USB) | 14 AWG | 14 AWG | 12 AWG | 12 AWG |
| 10 A (12V fridge) | 14 AWG | 12 AWG | 10 AWG | 8 AWG |
| 15 A | 12 AWG | 10 AWG | 8 AWG | 6 AWG |
| 20 A (fuse block feed) | 12 AWG | 8 AWG | 6 AWG | 6 AWG |
| 30 A (air compressor) | 10 AWG | 6 AWG | 6 AWG | 4 AWG |
| 50 A (DC-DC input) | 8 AWG | 4 AWG | 2 AWG | 2 AWG |
For metric sizes, 14 AWG is about 2 mm², 12 AWG about 3.3 mm², 10 AWG about 5.3 mm², 8 AWG about 8.4 mm², 6 AWG about 13 mm², 4 AWG about 21 mm² and 2 AWG about 34 mm². Also check that the wire’s current rating (ampacity) covers the load. For short runs, ampacity is usually the limit. For long runs, voltage drop is.
A worked example
Say your fridge sits on a slide in the cargo area, about 12 feet from an auxiliary battery under the hood, and draws up to 10A when the compressor starts. On the table, 15 feet at 10A needs 10 AWG. Many fridges ship with a 12V plug lead that is thinner than that, which is fine for its own short length. The long run from the battery to the socket is what needs the thick cable. So the usual fix is to run 8 or 10 AWG to a socket or fuse block in the back, then use the fridge’s own lead from there.
Where the fuse goes
A fuse protects the wire, not the device. If the cable shorts against the body, the fuse has to blow before the cable overheats. That’s why the fuse belongs at the power source end. Blue Sea Systems, quoting the ABYC E-11 marine standard, puts the fuse for a battery or charging source within 7 inches (175 mm) of the connection. If the cable is protected along its whole length by a sheath or conduit, that distance can stretch to 72 inches from a battery.
- Size the fuse to the wire. The fuse rating should be equal to or lower than the wire’s ampacity. Never fit a bigger fuse because the small one keeps blowing.
- Fuse both ends when a cable links two batteries or a battery and a DC-DC charger, because current can come from either side.
- Use a fuse block for small loads, fed by one properly fused cable. It keeps the battery terminals tidy and makes faults easier to find.
- Follow the device manual when it specifies a fuse. Then choose a wire rated above that fuse.
Practical tips for vehicle wiring
- Use fine-stranded tinned copper cable. It handles vibration better and resists corrosion.
- Crimp lugs with a proper crimper and cover them with adhesive heat-shrink. Twisted wire under a screw terminal works loose on corrugations.
- Protect cables where they pass through metal with grommets, and secure them every foot or so.
- Keep 12V cables away from exhaust heat and moving steering parts.
- Label both ends. Six months later, you’ll be glad you did.
If you’re still planning the whole system, start with our 12V power guide and our DC-DC charger guide. Our 12V power calculator will tell you how much current each device draws, which is the first number you need for this table.
FAQ
Can I use thicker wire than the table says?
Yes. Thicker wire only costs more and is harder to route. It never hurts performance.
Is it safe to do my own 12V wiring?
Low-voltage wiring is well within reach for many owners, but high-current cables can still start fires. If you’re not confident with crimping and fusing, ask an auto electrician to check your work.
Sources
The sizing table is our own calculation for copper wire at 12V and a 3% drop. It’s a guide, not a substitute for the device manufacturer’s instructions or a qualified auto electrician.
Featured photo: Maxim Hopman on Unsplash.


